B-800 Automatic Glue Dispenser
B-800 Automatic Glue Dispenser – Timed Adhesive dispensing Machine China Manufacturer
Please check above pictures of each button and knob’s function explanation, which will you help you quickly understand their use method. On the front panel, from left to right, we can see it has Power button, mode button, dispensing time setting knob, air pressure setting knob(needs to be pulled out before adjusting), vacuum knob, air-out socket. Its different point from normal machine is the VACUUM knob is made from metal. On the rear panel, from left to right is Air-in hole, DIP code key switches of 1, 2, 3, 4. foot pedal socket and power wire socket. Please note the foot pedal jack is 3-pin socket, which is different from 982 and 983A glue dispensing machine controllers. Don’t make mistake when you buy accessory of foot pedal for this dispenser.
Using the imported electromagnetic valve to make sure this adhesive dispenser has good quality and stable performance. It is widely suitable for Various solvents, adhesives, paints, chemical materials, solid glue, silica gel, EMI conductive adhesive, UV adhesive, AB adhesive, quick-drying adhesive, epoxy adhesive, polyurethane adhesive, sealant, hot glue, grease, Silver plastic, red plastic, solder paste, thermal grease, solder paste, transparent paint, screw fixer, wood glue, anaerobic adhesive, acrylic glue, anti-wear rubber, crystal glue, pouring glue, speaker glue, instant glue, rubber , paints, enamel paints, lacquers, inks, pigments, etc.
Because the function and usage is exactly same as 982 dispenser, please click below to know more about usage:
Applications of automatic glue dispenser
Electronics
Mobile phone button dispensing, mobile phone battery assembly, laptop battery assembly, computer speaker/receiver assembly, coil dispensing, PCB board bonding, IC sealing, speaker outer ring dispensing, PDA sealing, LCD sealing, IC assembly, IC bonding, chassis bonding, optical device processing, circuit components bonding to substrates, printed circuit board coating.
Lighting industry
Led fluorescent powder LED driving power supply thermal potting, hard light strip, soft light strip potting, bulb light, lighting, etc., LED street light bonding, flood light, lawn light and other outdoor lighting irrigating Seal, led lamp holder potting, LED spotlight cover and lamp cup bonding seal.
Automobile industry
Lamp assembly, electric vehicle controller assembly, filter (oil filter, diesel filter, air filter), car body and roof reinforcement plate glue, clutch and drive belt potting, window seal, plastic block Plate, radiator tank glue, automotive sensor glue filling, automotive electronics and vehicle electrical assembly, instrumentation potting protection, mechanical seals and other automotive machinery parts coating.
Instrumentation
Bonding and potting of capacitors, transformers, relays, buttons, etc., motor coils are glued, and electrical cabinet doors are glued.
Maintenance of pneumatic adhesive dispenser
The daily maintenance of the dispenser directly affects the lifespan. The daily work of the dispenser maintenance has a great influence on the service life, including the smoothness of the normal use process. The following are the daily maintenance steps of the dispenser:
- Clean the barrel If replacing the new type of glue.
- If the air intake is not normal, please check whether the air pressure source is smooth. Before using the glue in large quantities, please use a small amount of trials to master the product’s use skills to avoid mistakes. When the test is no problem, then carry out mass production.
- Please clean the machine part regularly to increase the service life. The more the amount of glue mixed together, the faster the reaction will be. Therefore, properly mix the glue according to the actual production situation, otherwise the glue will be wasted.
- When the machine is deactivated for a long time, the power should be unplugged, which will not only prolong the life of the machine but also save a lot of electricity.
Standard condiguration:
1pc controller machine
2pcs 30cc syringe
1pc air-in hose
1pc adaptor with hose
1pc foot pedal
1pc hand switch
5pcs tipss
1pc syringe stand
1pc power cable
1pc instruction book
Comes with 1pc controller machine, 2pcs 30cc syringes, 1pc air-in hose, 1pc adaptor with hose, 1pc foot pedal, 5pcs dispensing needles, 1pc syringe stand, 1pc power cable, 1pc instruction book.
Payment methods: T/T(Telegraphic Transfer), Western Union, MoneyGram, Paypal.
Payment Terms: Full payment before shipment.
Delivery Terms: EXW, FOB, CIF, DDU, DDP optional.
Shipping methods:
1)Door to Door - Via International Express: DHL/FedEx/UPS etc. - Shipping time: 3-7 days.
2)Door to Seaport - By sea: Maersk, MSC, CMA-CGM, Evergreen, Cosco, APL etc. - Shipping time: about 1 month.
3)Door to airport - By plane - Shipping time: about one week.