Digital Display Automatic Glue Dispensing Machine

Dispensing valve controller is also referred as glue dispenser or auto glue dispensing machine, which is a device used to control the fluids when applying to target area of products under specified ration at given frequency. It is an professional alternative to manual glue dispenser which is far from meeting the requirements of the industry following the development of automation technology and elevation of quality control. This dispenser machine adopts superior control hardware and software to ensure timed, quantitative and uniform dispensing during work. Mostly important, Using this glue dispenser can help users in lowering glue waste, improving work efficiency, raising the quality, and saving much cost.

It is applicable to integrated circuits, semiconductor packages, color LCD screens, electronic components such as relays, loudspeakers, electronic components, automobile components, etc.

Principle

Fluid is uniformly dispensed from an applicator at prescribed quantity each drop and at specified intervals under the control of a dispensing controller by means of the adjustment and regulation of air pressure acting on the liquid applicator.

1. Power switch: Red light for off, green light for on.
2. Testing button, with same function as foot switch.
3. Digital display to present some necessary information.
4. “Function”button, used for mode choosing and setting.
5. “UP”button, means the number increased.
6. “Down”button, means the number decreased.
7. “Auxiliary”button, used to select decimal point when setting, which moves one position each time you press.
8. Air pressure gauge, display the real-time air pressure during work of machine.
9. Pressure regulating valve, used to adjust the working pressure of machine in terms of different working conditions.
10. Connected to continuous air inlet on the dispensing valve(Air pressure output available after foot switch is pressed in auto mode. )
11. Connected to Controlled air inlet on the dispensing valve(Air pressure output available after foot switch is pressed in auto mode.)
12. Air intake
13. Connected to foot switch.
14. Power interface.

Hot to Use This Auto Dispensing Valve Controller

There are 4 different operating modes including Manual, Quantitative, Cyclical and Continuous.

1. Manual dispensing mode

Turn on the glue dispenser, press function key, indicating “1000” on the digital screen, which means that Manual mode is on: Long Press the foot switch to start dispensing fluid continuously until the pedal is loosened. Other keys are out of operation.

2. Quantitative dispensing mode

Turn on the machine, press “Function” twice, indicating “2000” on the digital screen, which means that Quantitative pattern is workable: When clicking the foot switch one time, the fluid will be dispensed automatically until the set time is up.

In this mode, long press “Function” button until “A000” is displayed on the screen, entering into dispensing time setting, press “+” or “-” and auxiliary button to select the required duration for each dispensing. After setup, press “Function” button to exit to “2000”.

3. Cyclical dispensing mode

Turn on the dispensing machine, press “Function” for 3 times, “3000” is displayed on the screen, which means cyclical mode is on: After clicking the foot switch one time, machine can dispense fluid for a period of time according to a preset value, then stop lasting for a duration based on a preset interval, then resume dispensing fluid again to repeat above procedure in cycle.

In this mode, long press “Function” button until “A000” is displayed on the screen, entering into dispensing time setting. Press “+” or “-” and auxiliary button to select the required duration for each dispensing. Press “Function” again, indicating “B000” on the screen, entering into dispensing interval setting. Press “+” or “-” and auxiliary button to select the required duration as interval. Press “Function” again, “C000” is shown on the screen, indicating loop setting. Press “+” or “-” and auxiliary button to select the required number of cycle, for example, If setting three “zero” for loop number, which means loop forever.

4. Continuous dispensing mode

Turn on the machine, press “Function” button, “4000” is displayed on the screen, indicating Continuous mode is on, Click the foot switch one time, fluid will be dispensed from applicator continuously until the second click on the pedal.

Features

1. The shell is made of corrosion resistant aluminium alloy, which is not only durable but also rigid enough to protect the components inside the controller.
2. Fitted with precision parts inside the controller to enhance the reliability, durability and stability.
3. Automatically intelligent control system to run the dispensing process, with quick reaction, high efficiency and precision dispensing.
4. As much as 4 different dispensing modes are available for users to choose throughout the test.
5. Equipped with a precision air pressure gauge for accurate regulation for dispensing.
6. Advanced digital system is employed to ensure evenly timed and quantitative dispensing.
7. Dispensing Valve Controller is compatible with various dispensing devices such as three axis machines, dispensing valves, pressure buckets.
8. Helps in realizing accurate dispensing, improving work efficiency and lowering the production cost.
9. Easy for users to operate.